Search results

The results of the investigations on the evaluation of efficiency use of the diesel locomotives UzTE16M4 in the mountainous direction Kumkurgan - Tashguzar of the Uzbek railways track by of the movement goods trains with stops and without any stops on the spaces station are presented.

The article proposes a method of calculation the load between the rolling bodies of the swinging bearings and the bearings of the traction motor, which makes it possible to have the value of the radial clearance in the bearing, as well as the radial movement of the inner rings relative to the outer one. To determine the load perceived by the most loaded rollers, a solution of the equilibrium equation for internal elements is proposed using simple iterations. The implementation of the method is implemented in the Matlab software package. Using the proposed method, the load distribution between the rollers in the traction motor of the VL11K electric locomotive was calculated. To determine the load acting on the bearing, the “Sarga-Subic” section was selected, which has a mountain profile.

The article includes research results of substantiation 3ТЕ10М diеsel locomotive`s movement work parameters on a hilly-mountainous direction of railway while moving freight trains with stops and without any stops on the spaces stations and separating points

The article includes research results of analyzing and evaluating 3ТЕ10М diesel locomotive`s efficiency on a hilly-mountainous direction Marokand-Navoi of Uzbekistan railways while hauling freight trains with and without stopping on through stations (division points).Main parameters of basic movement work of researched UzTE16M3 diesel locomotives are shown as tabled values and graphic dependencies,also equations of organizing necessary calculations mentioned above in accepted range of mass variation are marked here.

The experience gained in the operation of high-voltage vacuum circuit breakers VBO-25-20/ 630UHL1 indicates an incorrect assessment of the mechanical resource of its individual components and elements. Despite the repeated improvement of the design of the main switch drive, applicable both as part of the new «Ermak» series locomotives starting from number 1000 series, and in earlier numbers, the dynamics of malfunctions continues to persist to the present time. One of the most important elements of the main switch is a latch designed to hold the elements of the drive mechanism in the on position, the failure of the latch entails the failure of the entire section of the locomotive. The article considers three latch upgrades previously proposed by the manufacturer, a kinematic scheme of the drive with a vacuum arc-extinguishing chamber of the switch is developed, the parameters of the preload and trip springs in the drive are calculated, the forces operating during operation are determined. On the example of the latest modernization of the latch using the finite element method in the SolidWorks Simulation software package, a strength calculation was carried out, according to the results of which the stresses arising in its design were determined. As a result of the analysis of the finite element model, the forces critical for the structure are determined, a graph of the dependence of the structural strength margin and the maximum stress in the structure on the acting forces is developed. According to the results of the study, the force at which the most favorable value of the safety factor is provided is determined, for which it is proposed to reduce the critical force by changing the parameters of the compression springs and disconnecting the drive of the arc extinguishing chamber. A loading diagram with the drawing dimensions of two modified springs has been developed.

The introduced results of the investigation by valuation of efficiency the employment of the locomotives of the diesel (the diesel locomotives 3TE10M, UzTE16M3) and of the electrical (the electric locomotives 3VL80S) tractions in the plainly direction of railway track by the method of averagin design values. Modified average significances main indicator move working of the investigations of the diesel locomotives 3TE10M, UzTE16M3 of the evaluation mind numeral and table facts, and also graphic arts dependences, representative oneself arithmetical mean value with taking into account of the movement goods trains without any stops and with stops on the spaces stations, passing - tracks and divides points, which have received in the result to uses of the traction calculation for different conditions organization of the goods movement. Designate equations for organization calculation values mention exponents in the accepted range changing of the masses trains

The results of the investigations on the study condition movement of high-speed trains with active and passive systems inclination of body of the carriage in the curved directions of railway track with the registrations of the organizes in the movement and exploitation of the electric trains «Afrosiyob» in the direction Tashkent - Samarkand of the Uzbek railway track are presented are presented.

Features of the methods of calculation of a braking distance of the train applied now are considered. The main shortcomings of the most widespread method of definition of a braking distance on speed intervals are shown. Authors offered the new method of calculation allowing to consider critical parameters of process of braking (speed of a brake wave; character of an indicator diagram of the brake cylinder and mode of a brake; the actual initial speed for calculation of a way of action of brakes of the train). For verification of the offered method computer modeling is executed and the analysis of results of the different methods of calculation of braking length received at application is carried out. The new method allows to make calculation of braking length of the rolling stock more precisely.

The article proposes an approach to improve the efficiency of using the automatic train guidance system based on instantaneous traction calculations using the actual movement parameters according to current measurements of on-board systems of electric locomotives. A critical analysis of scientific research on the improvement of auto-guidance systems for freight mainline electric locomotives based on modern technologies and machine learning algorithms, neural networks has been carried out. As a rule, all existing approaches to determining the optimal train driving modes are based on the application of traction calculation rules with the empirical setting of movement resistances and other factors without taking into account the real influence of the external environment. The results of comparison of traction calculations in the section of the West Siberian test site according to the current rules and in the KORTES program with the actual data of the on-board measurement systems of the 2ES6 series electric locomotive are presented. Based on the data deciphered from the recorders of motion parameters of electric locomotives of the 2ES6 series, the laws of control of the excitation current at rheostatic and running positions in the traction mode are investigated. The possibility of using the measured data of the on-board systems of electric locomotives to determine the parameters of the train, including the torque of the traction motors, the traction force of the electric locomotive sections, the actual total resistance to movement, inertial properties, etc., is substantiated. The calculation of these parameters for the traction mode is performed. The concept of equivalent mass is introduced and expressions are presented for determining the parameters of a train based on the equation of motion in the form of small increments of measured and calculated data. The obtained results of determining the parameters of the train based on instantaneous traction calculations and data of current measurements of the on-board systems of electric locomotives showed statistical stability and can be used in real time for automatic train guidance systems, providing an increase in the accuracy of determining control actions, taking into account the actual influence of the external environment and increasing the efficiency of using the automatic guidance system for freight trains. locomotives in general.

The problem of the assessment of the continuous welded rail track stability at its thermal elongation is considered in this paper. The method for determining the stress-strain state of various elastic objects developed by the specialists of JSC “VNIKTI” is analyzed on the example of a rail of a continuous-welded track section. The essence of the method is to determine the dependence of the natural frequencies of rail vibrations on the applied longitudinal force. As a means of obtaining such a dependence, a modal analysis of a track section model carried out using the finite element method was chosen. The methodology for calculating the natural frequencies of rail vibrations and the description of the created model of the track section and its properties are presented in the paper, the contact interactions of the model elements and boundary conditions are defined in it. Calculations for determining the natural frequencies and modes of rail vibrations are performed, the first four modes of rail vibrations obtained by calculation and experimental methods are shown. The assessment of the adequacy of the created model of the track section is carried out by comparing the natural frequencies and modes of rail vibrations obtained by calculation, by modal analysis methods and experimentally when measuring vibrations on a full-scale object - assembled rails and sleepers, having a similar design compared with the model. It was decided to use the distance between the vibration nodes as a criterion for comparing the obtained modes of natural rail vibrations. The first mode of vibration is selected for further studies. Calculations were carried out and the dependence of the natural frequency of the first vibration mode of the rail on the longitudinal force applied to it was obtained using the created model of the track section. The obtained dependence can be used in the method proposed by the specialists of JSC “VNIKTI” in order to determine longitudinal force, applied to the rails on the full-scale section of the continuous welded rail track.

In this article, the problem of assessing the stability of a continuous welded rail track during its thermal elongation is considered. The article considers the method of determining a stress-strain state of continuous welded rails proposed by specialists of JSC “VNIKTI”, which is based on the use of the dependence of natural frequencies of rail vibrations on the applied longitudinal force. Such a dependence can be obtained with the help of the calculation method using a finite element model of a track section. The reliability of such a dependence can be assessed by comparing the results obtained using the calculation method with the actual values of natural frequencies of rail vibrations, depending on the longitudinal tensile and compression force applied to a full-scale facility. The track panel is chosen as such a facility. In order to obtain the actual dependence of natural frequencies of rail vibrations on the applied longitudinal force, a specialized test bench is developed. The development of the test bench included designing the test bench elements and creating finite element models of main load-bearing elements of the test bench - a stop, support and traction, as well as their subsequent strength calculation to confirm the operability of the selected design under necessary loading conditions. The strength is assessed using the safety factor for the yield strength. Calculations using the finite element method have shown that the test bench design has sufficient strength. The developed test bench will allow performing tests for the purpose of the verification obtained using the calculation method of the dependence of rail vibration frequencies on the longitudinal tension and compression force applied to it, as well as for testing the proposed method to assess the rail longitudinal force during its thermal expansion.

Transportation in tank cars of viscous liquid cargo (fuel oil, paraffins, industrial oils, cracking residues, etc.) is difficult with their solidification, accompanied by a sharp increase in viscosity. In fact, this leads to the need to warm up or partially warm up the transported oil product before unloading, usually carried out as a gravity discharge, in order to restore the fluidity of the delivered oil cargo. The process of unloading in this case with heating leads to a significant increase in the cost of transporting petroleum products, including the downtime of tank cars, and in general, a decrease in the turnover of rolling stock. According to the analysis carried out to determine the costs of the technological process of heating frozen petroleum products transported by rail, about 600 thousand tons of conventional fuel are spent per year, and the idle time of tank cars under unloading and subsequent cleaning of boilers from high-viscosity residues of oil cargo exceeds 1 million car-hours. The urgency of the issue of reducing the cost of railway transportation of viscous cargo is due to the intensive development of the Northern and Eastern regions of the Russian Federation. Important factors for transportation in these conditions are not only the negative average daily air temperature, but also long distances. The issue of reducing the cost of transportation of viscous petroleum products at low air temperatures is considered. Viscous petroleum products, when thickened, turn into a rheological liquid, which does not have a clear interface between the liquid and solid phases. The methods of transfer to the stratified state of hot fuel oil during its slow cooling and partial solidification with the formation of a heat-insulating layer of solidified fuel oil are applied. The positive effect is achieved by reducing the time and cost of thermal energy for unloading the delivered oil product by reducing the rate of its cooling during transportation. This, in turn, is achieved by suppressing the natural convection of the hot oil product on the cold walls of the boiler of the tank car in the first few hours after filling the tank. From the comparison of the experimental data and the calculation results, the values of the empirical coefficients of the equation for the heat transfer coefficient of liquid petroleum products are selected. The standard deviation of the absolute temperature of the liquid petroleum product was 8 %.

The article contains the main provisions of the methodology for determining the indicators of electric locomotives energy efficiency. The results of indicators calculations for electric locomotives of series 3ES5K, EP2K and 2ES6 are presented with reference to the current sections of railways. The proposed approach can be used to establish the level of energy efficiency of various series of electric rolling stock and their objective comparison when operating at different sites with trains of various masses with the aim of further creating an automated system for optimizing the use of traction resources of JSCo Russian Railways.

The article discusses the traction parameters of a new generation electric locomotive. The existing schemes of service areas by electric locomotives and locomotive brigades on the studied railway test site are presented. A comparison is made of the main parameters of DC and single-phase AC electric locomotives, the operation of which is currently organized on sections of movement with trains of calculated mass in the long-term mode of thrust on the climbs of various steepness. The scheme of the proposed organization of operation of a double power locomotive and locomotive crews is presented. Calculated traction parameters of a two-system electric locomotive, taking into account the plan and profile of the track in the proposed areas of operation, specific resistivity to the movement of the locomotive and the composition of the train at the estimated speed, specific accelerating and decelerating forces of the train. When two-system electric locomotives are put into operation, it will be possible to reduce the fleet of locomotives in operation, the number of traction arms due to their lengthening and the number of locomotive change points, reduce the transit time of freight trains, increase technical and local speed, average daily mileage and average daily performance of the locomotive, reduce power consumption per traction . The operation of such electric locomotives contributes to the development of polygon technologies for managing the transportation process, improving the quantitative and qualitative indicators of various railway enterprises.

The article deals with the modeling of the electric rolling stock and traction power supply system with the aim of solving the problem of reducing the electric power consumption for the traction of trains in the conditions of changing the schedule of freight trains. Simulation modeling is performed for the conditions of changing the mass of the train and the load on the axis. The description of the results obtained is based on regression models, the order of application of models in practice is given.

The article presents the results of the development and implementation of a method for controlling the technological processes of repairing locomotives based on network planning. The methodology allows you to track online bottlenecks during current repairs and reduce the duration of the critical path by varying the time indicators of events and works, using the aggregate-nodal repair method, redistributing resources between critical and non-critical works. The developed methodology is based on the adjustment of basic repair networks, taking into account the workload of process equipment and repair personnel, the availability of spare parts and materials, the need for unscheduled work during the planned installation of a particular locomotive for repair. This approach was implemented within the framework of the automated control system (ACS) «Network Schedule» and provides control and adjustment of the implementation of technological operations according to the indicators of technological preparation of repairs. An algorithm has been developed for determining a generalized performance indicator when assessing the quality of functioning of an automated maintenance and repair control system for a locomotive in service locomotive depots.